"We are using an Onsrud, Titanium Edge, Double Fluted cut-out bit. These bits are used with our C&C cutout machine. This machine cuts out steel doors to accommodate glass inserts. The cryogenic treated bits last approximately twice as long as regular, non-treated bits, saving us not only in the cost of the bits themselves, but also the time and labor necessary to replace the bit."  Kevin Connor from Crest Doors in San Antonio, TX

Joe used to change his Zenith Slitter blades every 21-28 days. Now he changes them every 43 days!  Joe Williamson from Ohio Packaging in Massillon, Ohio

Darrel uses 9/16 x 1/2 sockets to put caps on machined covers for ATV's. He used to get 2 days, after the cryo he gets 2 weeks!  Darrel Delong at Dana Corp in Black Lick, Ohio

"It does a fantastic job," he comments. The cryo process triples the life of his chipper knives, saw teeth and planer knives. "It saves labor and time and doesn't change the properties as far as being able to resharpen the tools."  Nathan Replogle of Replogle Ent. in Henry, TN.

"We normally have a tool change at 110 to 130 inches on our gundrills with C-3 carbide tips. Now, since we cryogenically treat them, we are seeing consistent 350-450 inches between sharpening."  Bill Crawford at Allied Machine in Dover, Ohio

"The cryogenic tempering process has significantly improved wear resistance and durability on two broaches we had cryogenically treated. They have broached over 500 rotors per broach and are still cutting clean. Prior to cryo, we broached 200 rotors."  Glenn Pisching at Lincoln Motors in Cleveland, Ohio

"Toolinsert (knives) Ticn coated cuts 2,800,000 parts. The same knife cryo treated 4,000,000 parts and still moving up!"  Wolfgang Stuchly at Julius Blum in Stanley, NC.

"Noticeable difference in wear. Less time changing knives. 2 to 3 times longer life. Less grinding to resharpen"  Larry Hunter at Pike Lumber in Akron, Indiana

"Trenching teeth for digging trenches for highway underdrain systems lasted 1 ½ times longer."  Kenneth Davies at Kokosing Construction in Fredericktown, Ohio

"Greatly enhanced performance of knife edge of calendar knives and Cameron cutter knives from every 1 ½ months to once a year."  Dominique Nero at Salem Republic Rubber Co. in Sebring, Ohio

"Treated end mills maintain better cutting edge capabilities giving a 5 to 1 ratio over non treated tooling. Exceptional wear and stability."  Dan Smarr at Stark Mold in Canton, Ohio

"4 times longer wear of steel pneumatic scissors cutting neoprene and rubber."  Terry Shaw at Goodyear Air Spring in Greensburg, Ohio

"Circular forming tools cutting glass filled Teflon are getting 4 to 5 times tool life between regrinds. Cryo treated milling cutters are doubling the life."  John Forrest at Forrest Screw Machine in Mansfield, Ohio

"We used 3-4 cobalt roughing end mills for a 60 piece run. After cryo we used 1 tool to run all 60 parts without any noticeable wear on the tool."  Tom Stugmyer at Ace Precision Ind. in Tallmadge, Ohio

"Treated slitter knives cutting corrugated paper went from lasting 2 weeks to 4-5 weeks after cryogenic treatment."  Jim Greenwood at Trey Corrugated in Sharonville, Ohio

"Chipper knives would usually last for one shift which would make 20-25 tons of chips. The cryo treated knives made 45-60 tons of chips. When changing the knives I’ve seen fewer nicks in the blades and they didn’t show any signs of burning."  John Blake at Brookville Wood Products in Brookville, Pa.

"Average life for untreated Stanley #11-911 blades was 4-5 days before cryo. Treated blades are lasting 8-14 days."  Ken Barna at Sentinel Consumer Products in Mentor, Ohio

"Treated blades granulated cooler product, lasted 3 times longer and did not produce smoke during the granulating process."  Ed Stake at Carlisle Tire & Wheel in Carlisle, Pa.

"Lathe tools lasted 4-5 times longer than the non treated tools."  E. L. Wilson at Conax in Buffalo, NY

"Non treated 1/16” carbide drills drilled 120 holes. Treated drills drilled 416 holes."  Ray Fowler at Federal Mogul Aviation in Liberty, SC.

"D-2 dies were normally line-side polished seventeen times in four months... after Cryo-treatment, once in three months."  Jim Rau at TABC< Subsidiary of Toyota Motor Sales

"Cryo-treated taps out-last untreated taps 5:1."  F. E. Myers Company

"S-7 turret punches went from 100 hits to 1200 hits."  Will-Burt Company