I used to change my Zenith Slitter blades every 21-28 days. Now I changes them every 43 days!
Joe Williamson from Ohio Packaging in Massillon, OH- Noticeable difference in wear. Less time changing knives. 2 to 3 times longer life. Less grinding to resharpen.
Larry Hunter at Pike Lumber in Akron, IN - Trenching teeth for digging trenches for highway underdrain systems lasted 1½ times longer.
Kenneth Davies at Kokosing Construction in Fredericktown, OH - D-2 dies were normally line-side polished 17 times in four months... after Cryo treatment, once in three months.
Jim Rau at TABC Subsidiary of Toyota Motor Sales - Greatly enhanced performance of calendar knives and Cameron cutter knives from every 1½ months to once a year.
Dominique Nero at Salem Republic Rubber Co. in Sebring, OH - It saves labor and time and doesn't change the properties as far as being able to resharpen the tools.
Nathan Replogle of Replogle Ent. in Henry, TN - Treated end mills maintain better cutting edge capabilities giving a 5 to 1 ratio over non treated tooling.
Dan Smarr at Stark Mold in Canton, OH - We used 3-4 cobalt roughing end mills for a 60 piece run. After cryo we used 1 tool to run all 60 parts.
Tom Stugmyer at Ace Precision Ind. in Tallmadge, OH - Treated slitter knives cutting corrugated paper went from lasting 2 weeks to 4-5 weeks after cryogenic treatment.
Jim Greenwood at Trey Corrugated in Sharonville, OH - Average life for untreated Stanley #11-911 blades was 4-5 days. Treated blades are lasting 8-14 days.
Ken Barna at Sentinel Consumer Products in Mentor, OH
Sawmills / Lumber
CryoPlus is an authorized dealer of Simonds knives!
Our cryogenically treated chipper knives are exceptionally tough and durable. Made of special steel alloy, these chipper knives are heat treated to stand up under the heaviest feed possible. They produce uniform chips and reduce fines to an absolute minimum. Their “cryo treated” durability increases production, saves grinding time and decreases your yearly use of chipper knives.
Major sawmill customers:
- Knox Hardwoods
- Patterson Chip
- DeNoone Lumber
- Mohawk Lumber
- Pike Lumber
- Replogle
- Brookville Wood Products
- Bruce Hardwood
- PalletOne of Indiana
Testimonials
- “It does a fantastic job," he comments. The cryo process triples the life of his chipper knives, saw teeth and planer knives. "It saves labor and time and doesn't change the properties as far as being able to resharpen the tools.”
Nathan Replogle of Replogle Ent. in Henry, TN - “Noticeable difference in wear. Less time changing knives.2 to 3 times longer life. Less grinding to resharpen.”
Larry Hunter at Pike Lumber in Akron, IN - “Chipper knives would usually last for one shift which would make 20-25 tons of chips. The cryo treated knives made 45-60 tons of chips. When changing the knives I've seen fewer nicks in the blades and they didn't show any signs of burning.”
John Blake at Brookville Wood Products in Brookville, PA
View Our Brochure
| Simonds Knives | |
|---|---|
| *Price above includes the purchase price of the knife | |
| 48" Counter knives | $47 each |
| 58" Counter knives | $61 each |
| 60" Counter knives | $64 each |
| 66" Counter knives | $68 each |
| 48" Precision, Combination (14 3/4" x 4" x 3/8") | $59 each |
| 58" Precision, Combination (19 5/8" x 4" x 3/8") | $74 each |
| 60" Fulghum, Combination (19 1/4" x 4" x 3/8") | $72 each |
| 66" Precision, Combination (21 1/2" x 3 15/16" x 3/8") | $77 each |
